INTELLIBAR MODEL 48 DRIVER DOWNLOAD

Print density and print speed go hand in hand and should be adjusted together from the control panel. Page 4 Contents Model Print Head Installation To install a new print head after removing the old one, proceed as follows, depending on your IntelliBar printer model. Page 17 General Information The ribbon is fed by the stepper motor and is controlled by the main board and LED sensor settings ribbon end sensor. Model 48 and To install the print head in the Model 48 or printer, proceed as follows.

Uploader: Karg
Date Added: 4 March 2018
File Size: 62.78 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 52421
Price: Free* [*Free Regsitration Required]

IntelliTech IntelliBar High Speed Barcode Printer 4×6 120 VAC 3.5 Amp Model 48TT

Unit Operation Changing Settings To configure the printer to meet unique job requirements, refer to the detailed menu tree in Figure Page Cleaning and Adjustments Table lists the print speeds supported for each IntelliBar model. Enter text from picture: IntelliTech shall not be liable in any event for any special, indirect or consequential damages jodel any damages whatsoever resulting from loss of data, profits or use, for any reason or in any action, Resolving the problem This document contains information intellibbar the capabilities that are supported on printer hardware from IntelliTech International.

By pressing ‘print’ button you will print only modfl page. The liner exits through the label release paper slot. If all your prior adjustments have not produced the quality of output you require, try adjusting the print density.

  A4TECH RFSOP-35A DRIVER

IBM Information on Printers from IntelliTech International – United States

Installing The Thermal Ribbon Setup Installing the Thermal Ribbon The printer comes with a start-up thermal ribbon roll that intelliba approximately 50 meters long. Guide the label strip away from the lower media guide and thread it onto the internal rewinder take-up spindle. Table in Section 5 lists IntelliBar print speeds.

With the exception of the Feed button, the control panel buttons will not work unless the printer is offline.

The printers are grouped by type of printer for example, laser printers, color laser printers, ink jet printers, dot matrix and line printers, and multi-function printers and are generally listed in ascending order. In addition, this section contains warranty information that you should read. Press the button again. Page Glossary-3 pressure sensitive label — label material with adhesive backing and protective silicone- coated release liner to permit it to adhere instantly to most surfaces with the application of slight pressure.

Turn the printer ON. mofel

The IntelliBar Models 48,and 88 have internal bar code generation capability. Unit Operation Self-Test Follow the printer self-test procedure in this subsection to verify that the printer is set up correctly. Setup Line up notch to mount Mount ribbon take-up spool.

IntelliBar M48 Standard Series Printers

Troubleshooting and Repair Slide the print head balance lever all the way to the left as viewed from the front panel for maximum-width labels 4. Load labels as described in steps 1 through 9 in the previous subsection. Two labels will feed consecutively.

Glossary-2 facestock — any paper, film or foil material that can be converted into labels. Or, create a printer configuration and see if it works. Changing Settings Unit Operation Changing Settings To configure the printer to meet unique job requirements, refer to the detailed menu tree in Figure None of the above, continue with my search.

  LG CD-ROM CRN-8241B DRIVER DOWNLOAD

Page Troubleshooting A. Page 59 Setup Attach adhesive patch on ribbon leader Guide ribbon over ribbon guide to take-up spool and wind spool plate. XHTML-Print is also targeted at printing in environments where it is not feasible or desirable to install a printer-specific driver and where some variability in the formatting of the output is acceptable.

IntelliBar M48 Network Series Printers

Appendix A Packing Appendix A Packing When packing the IntelliBar printer for shipping or moving, reuse the original shipping carton and packing materials. Be sure the bottom lip on the label guide is positioned in the label release paper slot as shown in Figure To allow for design and specification improvements, the information in this document is subject to change at any time, without notice.

Intellibar Ribbons Model 48 and Model 88 1. Section 6 Troubleshooting Jump to Section 5 This section contains troubleshooting information for isolating problems in the printer to a field- replaceable consumable item paper and ribbon or printer assembly.